318 cuts out really bad at times

cide · 08-22-2008, 07:02 PM

hey guys i have a 92 dodge ram 4x4 and some where alongs the lines of when we rebuild the trans and got it straight the motor is playing trixs .there was a lifter tapping so we replaced it. and now after it runs for 20 pr 30 min. it goes to loading up or something so i replace the map sensor fill fiter oxgen sensor and it still does this and i also remove the Air flow sensor and clean all the carben off of it.has a new distriburter cap . could it be a intake leak or what do you guys think .[and the help on the trans was really great got er fix right on up thanks]

Doc · 08-22-2008, 09:50 PM

Do any codes come up ?

Mixmastermerrill · 08-23-2008, 02:40 AM

M.A.F Sensor
Mass Air Flow! Sensor!
Replace.

cide · 08-23-2008, 06:31 AM

codes 12,22,55 and i think 12 has sometthing to do with batter being dicountected and 22 votage to high at cooling sensor and 55 end of reading . iguess these is correct. i,ll will replace the air flow today .what about the pressure regulater could it cause this i have left out one thing that mite be important when it start acking up you can mass the gas and its like its starven for fuel .the fuel pump has been replace maybe a year and half ago so i hopen its still good

cide · 08-23-2008, 03:57 PM

hey guys i replace the mass idle air flow sensor today and it seems to be loading up still have to mash the gas peddle to the floor to get it to crank then runs really crapy scips and won't take the gas and its idles kind of high at times and when in gear you can,t stomp or mash the gas padle hard for it won't take the gas.

cide · 08-28-2008, 06:41 PM

ok fuel pressure regerlator didn,t fix it either so what the chances of the alumin intake shernken when it get hot .would this cause it to suck air around the gasket if it didn't get a good seal when it was replace,d. causeing it to load up on the gas

Monacoman · 09-08-2008, 09:47 AM

easyest way to check it spray quick start around the intake and if the engine starts to rev high its a intake leak and can get a close area of where the leak is coming from

08-22-2008, 07:02 PM	#1 (permalink)
cide Junior Member Join Date: May 2008 Posts: 5	318 cuts out really bad at times hey guys i have a 92 dodge ram 4x4 and some where alongs the lines of when we rebuild the trans and got it straight the motor is playing trixs .there was a lifter tapping so we replaced it. and now after it runs for 20 pr 30 min. it goes to loading up or something so i replace the map sensor fill fiter oxgen sensor and it still does this and i also remove the Air flow sensor and clean all the carben off of it.has a new distriburter cap . could it be a intake leak or what do you guys think .[and the help on the trans was really great got er fix right on up thanks] Last edited by cide : 08-22-2008 at 07:04 PM.

08-23-2008, 06:31 AM	#4 (permalink)
cide Junior Member Join Date: May 2008 Posts: 5	codes 12,22,55 and i think 12 has sometthing to do with batter being dicountected and 22 votage to high at cooling sensor and 55 end of reading . iguess these is correct. i,ll will replace the air flow today .what about the pressure regulater could it cause this i have left out one thing that mite be important when it start acking up you can mass the gas and its like its starven for fuel .the fuel pump has been replace maybe a year and half ago so i hopen its still good Last edited by cide : 08-23-2008 at 06:36 AM.

08-23-2008, 03:57 PM	#5 (permalink)
cide Junior Member Join Date: May 2008 Posts: 5	hey guys i replace the mass idle air flow sensor today and it seems to be loading up still have to mash the gas peddle to the floor to get it to crank then runs really crapy scips and won't take the gas and its idles kind of high at times and when in gear you can,t stomp or mash the gas padle hard for it won't take the gas. Last edited by cide : 08-23-2008 at 08:18 PM. Reason: more systoms

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
nice build bad advice	Joel@lavinconstruction.co	General Technical Questions	5	04-27-2008 04:58 PM
help hydraulic clutch for 833? bad z bar	1cerberus4u	A-Body	2	04-18-2008 07:55 PM
How Unlucky? Bad hydraulic lifter	62sportsweep	B-Body	5	04-07-2008 04:38 PM

08-22-2008, 09:50 PM	#2 (permalink)
Doc MasterDebater Join Date: Jun 2008 Location: nw lower Meeeechigan Posts: 673	Do any codes come up ?

08-23-2008, 02:40 AM	#3 (permalink)
Mixmastermerrill Member Join Date: Jul 2008 Location: Fairbanks Alaska Posts: 40	M.A.F Sensor Mass Air Flow! Sensor! Replace.

08-28-2008, 06:41 PM	#6 (permalink)
cide Junior Member Join Date: May 2008 Posts: 5	ok fuel pressure regerlator didn,t fix it either so what the chances of the alumin intake shernken when it get hot .would this cause it to suck air around the gasket if it didn't get a good seal when it was replace,d. causeing it to load up on the gas

09-08-2008, 09:47 AM	#7 (permalink)
Monacoman Member Join Date: Dec 2007 Posts: 32	easyest way to check it spray quick start around the intake and if the engine starts to rev high its a intake leak and can get a close area of where the leak is coming from