yes that's right. the car is a 1962 dodge lancer GT. she started out with a 170 cu inch slant six. when i purchased the car i immediately swapped the old iron out for a 5.9 magnum from a 98 dakota and stormed the streets with this for quite a while. a few years ago i decided to go modern hemi. i bought everything i needed to get started with the conversion. had it all mocked up into place and then hotrod magazine did a feature on a 62 valiant that someone had done the swap of the hemi to. well this blew the wind out of my sails. (anyone who knows me, will tell you i for some reason have always had to be different). this discouraged me from the swap. and now you can imagine i needed to pursue "different". and that i am, by swapping in a boosted four cylinder.

[IMG][/IMG]

[IMG][/IMG]

[IMG][/IMG]

[IMG][/IMG]

[IMG][/IMG]

[IMG][/IMG]

[IMG][/IMG]

[IMG][/IMG]

[IMG][/IMG]

[IMG][/IMG]

[IMG][/IMG]

[IMG][/IMG]

[IMG][/IMG]

[IMG][/IMG]

 

Awesome Rick..... Keep the pics coming.... That is Bad Azz Dude !!!!!

 

Well this will be interesting to see. What transmission are you going to use?

What turbo set up will you go with?

I own an SRT4 and can provide you with a wealth of info if needed. But I'll assume you already know about them

 

thanks bob

 

the trans is an MA5 five speed, found in the pontiac solstice saturn skye h3 and colorado. right now just going with the factory turbo to get it up and running. then i will worry about something different. i don't know as much as you may think so i will probably confide in your knowledge of the srt4

rich

 

i picked up the turbo and manifold. along with the computer and harness. which now allowed me to continue on with my mock up

[IMG][/IMG]

[IMG][/IMG]

[IMG][/IMG]

[IMG][/IMG]

[IMG][/IMG]

[IMG][/IMG]

[IMG][/IMG]

 

i dont love 4 cyl engines. BUT i think thats is just GREAT. i all ways thought about a 4 cyl off of a slant 6. i guess you are doing it. go go go.

 

Thanks

 

It fit...

 

I would have never even thought of doing that...It is awsome new technology with old school car...I love the motor mount you made Cant wait to see it run and how it runs...What is the difference in horse power between the Turbo4 and the slant6????Bill

 

yes it did

 

slant six was around 140 hp. the srt4 is 230 hp before any tuning mods.

 

Torque diff? I'll bet the vehicle weights are similar, exciting build.

 

Slant six torque 170. Srt4 torque 245. Neon weight. 3295.lancer weight. 2200 lbs

Slant six engine weight. 450. Srt4 engine weight. 339 lbs

 

well my attentions have been on the body currently. i took the outer skin of a 70 barracuda and grafted it to the lancer hood. it has really changed the cars personality
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]

 

That hood looks awesome!!

 

thanks i thought it was cool

 

so i had every intention of building a rear wing for this. until i came up with this idea

[IMG][/IMG]
[IMG][/IMG]

i trimmed the outer skin from the crossfire decklid shell and used it as a plug and inserted it into the lancer lid.

[IMG][/IMG]

screwed it down and tack welded it

[IMG][/IMG]

here it is for a mock up visual

[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]

from there i took out the center styling line made a filler and finished welding everything in and finished it off with the required bodywork and then applied the primer

[IMG][/IMG]
[IMG][/IMG]

then i flipped the lid over and did a little bodywork to conceal the graft

[IMG][/IMG]

applied epoxy primer

[IMG][/IMG]

then i took what was left of the crossfire skeleton and trimmed out another needed piece to finish out the underside. here it is in place. looks lik it will work out with a few filler pieces added

[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]

 

Dang Rick...... That is turning out Awesome !!!!!

The Engine Fit under the hood and all ?

 

thanks Bob

 

well here it is. the under side of the trunk lid turned out fantastic.


[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]

 

Awesome! totally on-board with the build

 

thanks. keep watchin'

 

Cool build!

Totally deserving of a Dr. Frankendodge title.

 

thanks

 

That thing is an easy 400 wheel with some BPU+ action

 

translation?

 

Not Sure what that means ether.....

 

so i did the sanding on the primer. found a few minor details that needed to be addressed. took care of them and reprimed this time with urethane primer. it only got better.

[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]

 

So Far... That looks Awesome !!!!!