Good Morning
#1651
Super Moderator
Taking your boots off doesn't count Bob....🙂
#1656
Super Moderator
Last time I had to deal with that Bob the 360 had so much blowby from stuck rings it would push the dipstick out and blow oil on the bottom of the hood after I fixed the intake gasket....🙂
70k of short trips over nine years filled the 360 full of carbon and sludge.....
70k of short trips over nine years filled the 360 full of carbon and sludge.....
#1657
I always find myself rationalizing my long-held beliefs about what "clean" means after my elbow grease starts to run low;
"If all the gunk is flat, things will still line up for a good seal. Once I close this up, I won't be able to see how bad it is anymore."
That devil on my shoulder is clever. Have to remind myself that he doesn't want my car to run right. He wants me to have to re-do simple work and suffer.
#1658
Mopar Lover
Thread Starter
Well... Long story short.... WE have a bert # 5 cylinder intake valve... Sooooo, Off with the heads and shipping them off to the machine shop for a repair and freshen up...
Just an FYI for those who are looking... This is a Mopar Performance Magnum 9.5.1 Short block with LA heads on it. Using a 268H Comp-Cam... And Yes it Pings if you get after it. Quench is all wrong on these with Iron stock heads.
Just an FYI for those who are looking... This is a Mopar Performance Magnum 9.5.1 Short block with LA heads on it. Using a 268H Comp-Cam... And Yes it Pings if you get after it. Quench is all wrong on these with Iron stock heads.
#1659
Super Moderator
Bob what is a bert valve? Is that like a warbler bearing?
I just remember your an old hillbilly, bert valve.......
I just remember your an old hillbilly, bert valve.......
Last edited by Iowan; 04-19-2019 at 01:10 PM.
#1661
Super Moderator
Uncontrolled detonation I think is what he is referring to.
#1662
Mopar Lover
Thread Starter
Well.. lol... working these little phone buttons and fat fingers and spelling correct just gets me sometimes..lol But I know y’all get it. And yes that is what I was referring to.
#1663
Damage to the pistons and valves and all that. But the real shame is ruining that beastly idle he must be getting from that cam! Haha!
Edit:
Just as well you had to take the top end apart. Looks like it would appreciate a nice hot detergent bath.
Edit:
Just as well you had to take the top end apart. Looks like it would appreciate a nice hot detergent bath.
#1664
Super Moderator
Looks like it needs better quality valve seals........
#1665
Mopar Lover
Shawn found a Viper Fiberglas body in Florida, anyone have an idea how to get it to Ontario Canada?
Yesterday took out a wall at other son’s house, too sore today to do anything.
#1670
Super Moderator
Well I picked up the boy at school today and he wanted to go fishing, he had made plans with his best buddy that we were going fishing. Now I don't know how many of you have gone fishing with a pair of eight year old boys that have a full load of **** and vinegar but it's a good time. My favorite is the only tree on the riverbank and a clear 100 yards of open shoreline on both sides, both of them cast into the tree. Frogs rocks dead fish all had there attention. Not a fish caught.
It just doesn't get better than this!
It just doesn't get better than this!
#1671
Mopar Lover
Thread Starter
Well,,, That's what we call "Kid Fishing"....lol Had a great time we hope....
Theirs kid fishing and Papa's fishing..... One day they will get it.... Good times !!!!!!! Making memories and some good laughs is what it's all about !!!!!!!
Theirs kid fishing and Papa's fishing..... One day they will get it.... Good times !!!!!!! Making memories and some good laughs is what it's all about !!!!!!!
#1672
Mopar Lover
Thread Starter
Good Morning Y'all….. TGIF.... I'm Working on getting the old Dodge back to running. Heads are back from the machine shop. She is fighting every step of the way. Now I am having to "Make Chips" of a Aluminum Manifold to fit... I wish the Emission Requirements / Restrictions would go away so I could put a descent engine together for this thing. Good Smog parts are getting hard to come by, they seem to be all pieced mealed together... Dam California
Oh Well... I'm done Crying about it.... Moving on
What are you working on this weekend??????
Oh Well... I'm done Crying about it.... Moving on
What are you working on this weekend??????
#1673
Mopar Lover
Thread Starter
Good Morning Y'all...... Hope you are all having a great day? Finishing up the final touches on putting the old 1977 Dodge D150 Warlock 360 back together. I'll try to get some photos up for y'all....
#1676
Super Moderator
Well it was 80 degrees her just a few days ago and it is SNOWING today!
Fricking Iowa! 🤨
Fricking Iowa! 🤨
#1678
Super Moderator
I like the dust on the air cleaner, it's like you didn't touch a thing! 🙂
#1679
Mopar Lover
Thread Starter
Customer Satisfaction Brother!!!! lol Glad you noticed...
Hope you got better weather today?
We got some Morning Clouds... May get a few sprinkles tonight... SO-CAL LOVE !!!
Oh Ya.... And I Finally put on the Edelbrock Performer that I had laying around for like 5 years...lol The old one I had wore a hole in the coolant passage, so I had installed the cast Iron one. Nice to get that PIG off the motor...
Hope you got better weather today?
We got some Morning Clouds... May get a few sprinkles tonight... SO-CAL LOVE !!!
Oh Ya.... And I Finally put on the Edelbrock Performer that I had laying around for like 5 years...lol The old one I had wore a hole in the coolant passage, so I had installed the cast Iron one. Nice to get that PIG off the motor...
Last edited by RacerHog; 04-28-2019 at 08:15 AM.
#1680
Mopar Lover
Customer must want reliable performance, not pretty. You'd think the customer might tidy it up a bit when he got it home, maybe he looks just like his truck.