440 stainless exhaust studs?
Thread Starter
New Member
Joined: Jan 2018
Posts: 12
Likes: 0
From: Buckingham, U.K.
440 stainless exhaust studs?
Hi all,
My first post here! I have a '72 Jensen Interceptor that I'm doing some work on at the moment. The question I hope you guys can help with is where I can get a set of stainless exhaust studs for the motor, which is a Chrysler 440 big block. ARP don't seem to list them specifically but I thought you might know if any of the studs ARP make for other cars might be suitable? I'm in the UK so ordering from Summit on the off chance is not really an option! Already ordered a load of bolts and the won't fit with the headers I have, aargh!
Any advice gratefully received!
My first post here! I have a '72 Jensen Interceptor that I'm doing some work on at the moment. The question I hope you guys can help with is where I can get a set of stainless exhaust studs for the motor, which is a Chrysler 440 big block. ARP don't seem to list them specifically but I thought you might know if any of the studs ARP make for other cars might be suitable? I'm in the UK so ordering from Summit on the off chance is not really an option! Already ordered a load of bolts and the won't fit with the headers I have, aargh!
Any advice gratefully received!
Thread Starter
New Member
Joined: Jan 2018
Posts: 12
Likes: 0
From: Buckingham, U.K.
Mopar Lover
Joined: Jun 2013
Posts: 11,071
Likes: 953
From: Monrovia SO-CAL (USA)
At any rate... Take a look into the Marine side of the industry....See if these are long enough for your need. 
http://www.hardin-marine.com/p-13555...-stud-kit.aspx
Jensen is a cool Down under Ride...
http://www.hardin-marine.com/p-13555...-stud-kit.aspx
Jensen is a cool Down under Ride...
Thread Starter
New Member
Joined: Jan 2018
Posts: 12
Likes: 0
From: Buckingham, U.K.
I'm using a header, of the 'block hugger type' like this:
From the layout you'll see why I can't get bolts into the flange holes by the outer pipes! The studs I have are the original ones, used with the factory iron manifolds. FYI. the new headers flange thickness is 1/4".
From the layout you'll see why I can't get bolts into the flange holes by the outer pipes! The studs I have are the original ones, used with the factory iron manifolds. FYI. the new headers flange thickness is 1/4".
Thread Starter
New Member
Joined: Jan 2018
Posts: 12
Likes: 0
From: Buckingham, U.K.
At any rate... Take a look into the Marine side of the industry....See if these are long enough for your need.
http://www.hardin-marine.com/p-13555...-stud-kit.aspx
Jensen is a cool Down under Ride...
http://www.hardin-marine.com/p-13555...-stud-kit.aspx
Jensen is a cool Down under Ride...
Thanks for that link, I think that's what I'm after!
New Member
Joined: Jan 2018
Posts: 1
Likes: 0
From: PortCharlotte Fl
Question 1972 Charger
Hi, I have an electrical problem with my 1972 Dodge Charger.
The problem is I have no power on my fan switch. The car has air conditioning also. So it's a 4 prong connection at the fan switch. The wires are two tans, a light green and a dark green. I am getting power out of the fuse block, which is a black wire with a white stripe, 16 gage wire. Followed the black and white stripe wire into the dash. Can anyone tell me where that wire goes? Any ideas of why I am not getting any power at the fan switch?
Thank you, Dan
The problem is I have no power on my fan switch. The car has air conditioning also. So it's a 4 prong connection at the fan switch. The wires are two tans, a light green and a dark green. I am getting power out of the fuse block, which is a black wire with a white stripe, 16 gage wire. Followed the black and white stripe wire into the dash. Can anyone tell me where that wire goes? Any ideas of why I am not getting any power at the fan switch?
Thank you, Dan
Thread Starter
New Member
Joined: Jan 2018
Posts: 12
Likes: 0
From: Buckingham, U.K.
Update on the stud saga....
Hi Bob,
I gave some dud info before re. The headers, the flange is of course not a 1/4” but 3/8”! Anyway the original studs are 1 3/4” OAL being 1/2” of coarse and 1” of fine.
I think I’m going to try a set of ARP 420-1401 studs that are a wee bit shorter at 1.670 OAL but have the same amount of coarse thread.
I gave some dud info before re. The headers, the flange is of course not a 1/4” but 3/8”! Anyway the original studs are 1 3/4” OAL being 1/2” of coarse and 1” of fine.
I think I’m going to try a set of ARP 420-1401 studs that are a wee bit shorter at 1.670 OAL but have the same amount of coarse thread.
Mopar Lover
Joined: Jun 2013
Posts: 11,071
Likes: 953
From: Monrovia SO-CAL (USA)
Hi, I have an electrical problem with my 1972 Dodge Charger.
The problem is I have no power on my fan switch. The car has air conditioning also. So it's a 4 prong connection at the fan switch. The wires are two tans, a light green and a dark green. I am getting power out of the fuse block, which is a black wire with a white stripe, 16 gage wire. Followed the black and white stripe wire into the dash. Can anyone tell me where that wire goes? Any ideas of why I am not getting any power at the fan switch?
Thank you, Dan
The problem is I have no power on my fan switch. The car has air conditioning also. So it's a 4 prong connection at the fan switch. The wires are two tans, a light green and a dark green. I am getting power out of the fuse block, which is a black wire with a white stripe, 16 gage wire. Followed the black and white stripe wire into the dash. Can anyone tell me where that wire goes? Any ideas of why I am not getting any power at the fan switch?
Thank you, Dan
Also. You can start your own thread on the subject over on the home page.... Keep us posted...
Thread
Thread Starter
Forum
Replies
Last Post
moparfreak66
Engines, Exhaust and Fuel systems
6
Jun 30, 2013 08:41 PM
Mopar Nut
Engines, Exhaust and Fuel systems
4
May 2, 2012 12:25 AM
